Skip to main content

Rack-and-pinion Steering

-

Rack-and-pinion Steering

Rack-and-pinion steering is quickly becoming the most common type of steering on cars, small trucks and SUVs. It is actually a pretty simple mechanism. A rack-and-pinion gearset is enclosed in a metal tube, with each end of the rack protruding from the tube. A rod, called a tie rod, connects to each end of the rack.
The pinion gear is attached to the steering shaft. When you turn the steering wheel, the gear spins, moving the rack. The tie rod at each end of the rack connects to the steering arm on the spindle (see diagram above).
The rack-and-pinion gearset does two things:
  • It converts the rotational motion of the steering wheel into the linear motion needed to turn the wheels.
  • It provides a gear reduction, making it easier to turn the wheels.
On most cars, it takes three to four complete revolutions of the steering wheel to make the wheels turn from lock to lock (from far left to far right).
The steering ratio is the ratio of how far you turn the steering wheel to how far the wheels turn. For instance, if one complete revolution (360 degrees) of the steering wheel results in the wheels of the car turning 20 degrees, then the steering ratio is 360 divided by 20, or 18:1. A higher ratio means that you have to turn the steering wheel more to get the wheels to turn a given distance. However, less effort is required because of the higher gear ratio.
Generally, lighter, sportier cars have lower steering ratios than larger cars and trucks. The lower ratio gives the steering a quicker response -- you don't have to turn the steering wheel as much to get the wheels to turn a given distance -- which is a desirable trait in sports cars. These smaller cars are light enough that even with the lower ratio, the effort required to turn the steering wheel is not excessive.
Some cars have variable-ratio steering, which uses a rack-and-pinion gearset that has a different tooth pitch (number of teeth per inch) in the center than it has on the outside. This makes the car respond quickly when starting a turn (the rack is near the center), and also reduces effort near the wheel's turning limits.

Power Rack-and-pinion

When the rack-and-pinion is in a power-steering system, the rack has a slightly different design.
Part of the rack contains a cylinder with a piston in the middle. The piston is connected to the rack. There are two fluid ports, one on either side of the piston. Supplying higher-pressure fluid to one side of the piston forces the piston to move, which in turn moves the rack, providing the power assist.
We'll check out the components that provide the high-pressure fluid, as well as decide which side of the rack to supply it to, later in the article. First, let's take a look at another type of steering.

Comments

Post a Comment

Popular posts from this blog

Meaning of 1.2L, 1.4L, 1.6L,engine in a car?

-
Image
In a car, which has a multi(4/6/8) cylinder engine, the above nomenclature viz. 1.6L,1.4L, etc. refers to the combined volume capacity of all the cylinders( expressed in cubic centimeters, 1L=1000 cc).  Here volume capacity refers to the swept volume or displacement volume or breathing capacity of the cylinder. It is basically the volume of air that can be sucked insde the cylinder as the stroke moves from TDC to BDC. Swept Volume,  V= pi/4*d^2*L*K   , where                                            d- Bore, L-Stroke,  K-no. of cylinders. This is the common terminology used to specify the engine size. A 1.2L engine means a 1.2 litre engine, which is equal to 1200cc (cc = cubic capacity).  Hope that explains it! Pros/Cons: Usually, hig...
Read more

Difference between a muffler and a catalytic converter

-
Image
A muffler makes the  car  quiet, the cat makes the exhaust clean. Cars built after 1974 originally had both, but it's legal to run with no muffler as long as the car isn't too loud. The cat is required, you can't pass emissions without one. Some people will remove the cat, if they live in a county without  emissions testing , but that is illegal. If you have a car with no  catalytic converter , and the muffler goes bad, sure you could put a cat on instead. They're more expensive, and louder, but that would get you legal. Actually, the cat is supposed to be mounted closer to the engine, where there is more exhaust heat to burn off exhaust crud. I suppose if you wanted to, you could run two catalytic converters. That would greatly restrict your exhaust and cut down on horsepower, probably reduce fuel economy as well. Probably wouldn't help emissions, either. hey are two totally different things,each with it's own  seperate purpose. You could put 2 co...
Read more

Nitrox suspension - Gas charged suspensions

-
Image
The advantages of using a Nitrox suspension - Gas charged suspensions. The rear shock absorbers on current Bajaj Pulsar series bikes are also popularly known as NITROX shock absorbers . These types of shock absorbers are actually called as ‘Gas Filled Shock Absorbers’. The visual differentiation between a conventional shock absorber and a gas filled shock absorber is a small canister (box) which is attached on one side of it. This canister holds a small amount of Nitrogen gas in it. Hence these hydraulic shock absorbers or dampers are called as gas filled shock absorbers. So what is the reason to use a gas filled hydraulic dampers instead of using a conventional one? we'll find out the answer here. The 'Royal Enfield - Bullet Electra' was the first bike in India to have this feature. The Pulsar 150/180 UG II (2’nd upgrade) then became the second model (and the first in the 150 cc and above category) to make this feature available on Indian bikes. A ...
Read more